CPU
8031 / 8051 operating at 11.0592 MHz
MEMORY
EPROM1 32KB bytes with monitor software
EPROM2
Optional – 32KB ROM
RAM1
32 KB Data RAM
RAM2
32 KB program/Data RAM
I/O PARALLEL
48 I/O lines using two 8255
I/O SERIAL
0ne RS232 compatible interface
TIMER
Three 16 bit counter /timer using 8253
KEYBOARD
Consisting of 28 numbers of computer grade keys
DISPLAY
Six numbers of seven segment displays
BUS SIGNALS
All bus signals are terminated in berg stick. Controller specific lines like port 1 lines TO T1, INTO, INT1, etc. are terminated in a burg stick header
MONITOR SOFTWARE
32KB of powerful user friendly monitor software with keyboard and serial modes

 

 

CPU
8031 / 8051 operating at 11.0592 MHz
MEMORY
EPROM1 32KB bytes with Monitor Software
EPROM2
Optional – 32KB ROM
RAM1
32 KB Data RAM
RAM2
32 KB Program/Data RAM
I/O PARALLEL
48 I/O lines using two 8255
I/O SERIAL
0ne RS232 compatible interface
TIMER
Three 16 bit counter /timer using 8253
KEYBOARD
External PC-AT Keyboard
DISPLAY
Alphanumeric LCD module(2 Lines x 16 characters)
BUS SIGNALS
All bus signals are terminated in FRC connectors. On chip port lines P1.0 to p1.7 TO, T1, INT1, INTO are also terminated
MONITOR
SOFTWARE
32KB of system monitor, which allows the user to enter, verify, debug or execute the program either from the on-board PC keyboard and display or through serial mode. On-line assembler using PC keyboard and LCD display

 

 

CPU
8031 / 8051 operating at 11.0592 MHz
MEMORY
EPROM1 32KB bytes with monitor software
RAM
32 KB program/Data
EPROM2
Optional – 32KB ROM
I/O PARALLEL
24 I/O lines using 8255
OTHER FEATURES SAME AS SDA – 31ME EXCEPT TIMER (8253)

 

 

In System Programmable 89C61X2 Microcontroller board

Philips 89C61X2 8 bit Microcontroller with 64K bytes in system Programmable Flash memory
Operating at 11.0592Mhz with external crystal
RS232 C compatible serial Interface; also needed during In System Programming
On board two digit, Seven Segment display and 4 key pad
On board Interface to LED and two push buttons
Ports 0,1 & 2 are terminated in a 26 pin FRC connector and is compatible with ALS standard external interfaces
Two FRC connectors (10 pin and 20pin) for connecting to external interfaces
Power supply provided through 9 pin D-Sub male connector
A number of interface models are available that allow the user to conduct specified experiments

 

FLASH PROGRAMMABLE EVALUATION BOARD
SPECIFICATIONS
Flash programmable AT89C51ED2 microcontroller with operating frequency of 11.0592Mhz. The controller has 64KB of in system programmable flash memory
1792 bytes of external (XDATA)RAM & 2048 bytes of EEPROM. On chip peripherals like timers, SPI interface, programmable counter array (compare/capture & PWM)UART and general purpose I/O ports provide enhanced features.On board LED’s, On board push button switches,
16x2 line LCD alphanumeric displayRS 232 C compatible serial interface for
Communication, ISP, SPI compatible 2 channels 12 bit ADC with temperature sensor
Interface, A 26 pin FRC connector CN3 connected to ports 0,1 & 2 of the controller for
Easy interface to ALS standard external interfaces In system programming capability,
Compact & elegant enclosure, Operates of 5V DC power.

 

 

CYGNAL C8051F020 CONTROLLER BOARD
Cygnal’s C8051F020 Higher end Microcontroller operating at a Frequency of 18.432 MHZ with an External Crystal and a supply voltage of 3.3 V
A low-noise low drop out Regulator to provide a voltage of 3.3 v as required by the controller
A 26-pin FRC connector is compatible with our standard external experimental interfaces
An 8-pin berg consisting of SMBUS (System Management Bus) signals for communication with an RTC DS1307 and an External Interrupt line
A 10-pin Header for In System Programming / Debugging of FLASH through JTAG with the help of a serial adapter, provided with the Evaluation kit
PERIPHERAL EXPANSION BOARD
The Peripheral Expansion Board based on External Memory Interface Consists of
A 60-pin FRC connector for Bus connection
An 8-pin berg for System Management Bus lines and External Interrupt line
RTC (DS 1307 Read & Write through SMBUS), LCD display and ASCII keyboard, interface through 8255 PPI (the ASCII keyboard interface is implemented as a parallel 8 bit with handshake connection between the 8255 and an on card 89C2051 Microcontroller which connects to an external keyboard), 32KB External RAM, Additional 8255 for other standard interfacing purposes, RS-232 serial interface (through UART0), RS-485 serial interface (through UART1)
CONTROLLER INTERFACE JIG
The Controller Interface Jig consists of the following:
A 20-pin FRC Connector which connects to the Controller Board for studying the features of the controller like Analog Comparator, 8-bit ADC, 12-bit ADC, 12-bit DAC, PCA (programmable counter array) features (8-bit PWM, 16-Bit PWM, HS o/p, S/W Timer etc,) Internal Counter/Timers and External Interrupt
A 26-pin FRC Connector which also connects to the Controller Board and interfaces to two 7 –segment Displays, 3x3 Keyboard Switch Matrix, two Push buttons, two Switches, two LEDs and a 4-way DIP switch
CYGNAL C8051F020 MICROCONTROLLER
SPECIFICATIONS
High-Speed pipelined 8051-compatible CIP-51 Microcontroller Core. Execution speed of up to 25 MIPS at the clock frequency of 25 MHZ
64KB of In System Programmable FLASH. 4352B of Internal Data RAM (4KB+256B)
Supply Voltage: 2.7V to 3.6V Precision VDD monitor/Brown out Detector and on chip watch dog Timer
On chip JTAG Debug and Boundary Scan. C8051F020 controller consists of the following configurable features : One 12-bit ADC, one 8-bit ADC, two 12 bit DACs, two voltage comparators, one Hardware SMBUS (System Management Bus) for two wire Serial communication, two UART Serial Ports (UART0 and UART1), one SPI (Serial Peripheral Interface) capable of providing full duplex Serial communication, Programmable Counter Array (features like Edge capture, Software Timer, High Speed output, Frequency Output, 8-bit and 16-bit PWM), five general purpose 16-bit Timer/Counters, Eight 8-bit ports (P0-P7)

 

 

Micro-controller with 256 bytes of on-chip RAM and 512 bytes of on-chip EEPROM
Operation in expanded mode with 28KB battery backed RAM for user Programs
4KB of powerful Monitor ROM
One analog I/P through potentiometer for studying internal ADC
All address, data and control lines are terminated in a 60 pin connector for external connection
One PPI using 8255 with 24 I/O lines terminated in a standard 26-pin FRC header
A number of programs that highlight the use of the micro controller
Operates on 5V DC, 500mA

 

 


CPU
80C196 CPU @ 12MHz. On-chip features such as 488 bytes of Internal RAM. Serial Port. 8 Channel multiplexer. S/H 10 bit A/D Converter. Two 16 bit Timers. 4 High speed Input lines. 6 High speed Output lines. 3 PWM outputs. Watch Dog Timer.
MEMORY
60K MAX memory organised as 30K Words of 16 bit each. Combination of Program and Data space with 3 possible RAM/ROM combinations through jumpers. Battery back-up option for RAM. Note : System is provided with 32k Monitor EPROM and 64K RAM.
SERIAL INTERFACE
Serial port using 8251
DIGITAL
I/O 48 I/O lines terminated in two 26 pin berg strip headers using 8255.
TIMER
Three 16 bit counter / timers using 8253.

 

 
ALS-PIC-02 PIC MICRO CONTROLLER KIT
The ALS –PIC-02 is a low cost, powerful, Run Time Trainer that works with a PC. This tool is based on the FLASH PIC 16F877. The module consists of an RJ 45 interface to PIC-DBUG-87X . The ports of the application controller are terminated in FRC headers. Development boards are provided which can be connected to the trainer and various experiments can be carried out. On board 4 Digit 7 Segment Display, 2 push buttons, 1 LED, Wakeup & Reset push Buttons are provided
PIC-DBUG-87X PIC DEBUGGER
The PIC Debugger enables a designer to develop and Debug source codes by watching variables, Single-Stepping and Setting Break Point. Running at full speed enables testing hardware in real-time. The Debugger is also a programmer for the flash PIC 16F87X. The debugger connects to the main board. The debugger can also be used to debug user’s 16F87X target boards
Note
 A number of interfaces like Stepper Motor, Water level measure, Load, temp DC Motor, Elevator, etc., can be interfaced

 

 

SPECIFICATIONS
Features of ATMEL AT89C51ED2

On-chip

64KB flash Program memory.
1792 bytes Expanded RAM (XRAM).
2048 bytes EEROM.
SPI interface.
16-bit Programmable Counter Array for Compare, Capture, PWM.
Three programmable Timer/Counters.
Two External Interrupts.
Operating Frequency – 11.0592 MHz.
RS232 compatible serial interface for communication and ISP
Alphanumeric 16x2 LCD display with back lighting
Two nos of general purpose LED’s.
Two-no.of general purpose push button Switches.
A Push button switch for Reset and a Slide switch to select either program mode or run mode.
Four no. of 8-pin single row Berg Sticks connected to PORT 0 to PORT 3.
Power Adaptor (5V, 1A.)
Evaluation version of ‘C’ compiler.
Demo programs for LCD, USART, LED switches.
16 nos Flying leads with female bergs for extending IO lines

 
SPECIFICATIONS
Features of ATMEGA128L

On-chip

128KB flash program memory.
4KB Internal Static RAM (SRAM).
4KB of internal EEPROM.
53 Programmable I/o lines.
On chip JTAG debugging and programming capability.
On chip In-System Programming (ISP) Capability.
Two 8-bit Timer/Counter and Two 16 –bit Timer/Counter
Capture, Compare and PWM modules.
On chip 8 Channel, 10-bit ADC module.
Dual Programmable Serial USART’s.
Master/Slave SPI Serial Interface.
On-chip Two wire Serial Interface (I2C)
Watchdog Timer with On-chip oscillator.
Eight external Interrupts.
Operating frequency 8 MHz.
16x2 alphanumeric display (LCD) with back lighting.
RS232 Serial interface through on chip UART0 or UART1 and 9 pin D-sub connector.
Two nos of general purpose LEDs and one power on LED.
Two nos of general purpose push button switches. A push button switch SW1 for Reset.
Four nos of 16-pin single row berg sticks connected PORT A to PORT G
ISP downloading tool to download the code to controller Flash memory.
Demo programs for LCD, USART, LED and Switches.
Evaluation version of ‘C’ compiler.
Demo programs for LCD, USART, LED switches.
16 nos Flying leads with female bergs for extending IO lines

 

 

SPECIFICATIONS
Two sided solder masked FR4 PCB with plated through holes at 2.54mm pitch
Supply and ground tracks for ease of connection
Berg pins for connection to project boards using flying leads
Size 11 x 23 cms

 

 

SPECIFICATIONS
 

Interfacing with SPI devices

12 bit DAC
256K EEPROM
12-bit ADC
  Interfacing with I2C devices

RTC WITH LI-ION BATTERY
16K NVROM
8-bit DAC
Compare, Capture and PWM interfaces
On-chip Comparator test interface.
Provision for testing on-chip ADC.
RS485 interface.
Push button for external Interrupt testing.
Two no. of General purpose LED’s.
Oscillator provision for testing on-chip RTC.
Provision for Pulse Input for testing counters.
Berg sticks for connecting above interfaces to project board using flying leads.

 

 

SPECIFICATIONS
  Features of PIC18F8680:Program memory-64kb.

Data memory-3328bytes, EEPROM memory-1024 bytes.

Four external interrupt pins.

Four programmable Timer/Counters.

One Capture/Compare/PWM (CCP) module.

SPI, I2C, USART (RS232, RS485), CAN.

16-channel, 10bit ADC.

In-Circuit Serial Programming™ (ICSP™) via two pins.

MPLAB® In-Circuit Debug (ICD) via two pins Operating Frequency - 10
       MHz.
RS232 compatible serial interface for communication and ISP.
Alphanumeric 16x2 LCD display.
Two nos of general purpose LED’s.
Two-no. of general-purpose push button Switches.
A Push button switch for Reset and a Slide switch to select either program mode or run mode.
Four no. of 20-pin single row Berg Sticks connected to Port A to Port H, Port J.
Power Adaptor (5V, 1A.)
PIC CCS Evaluation Version.
Demo programs for LCD, USART, LED switches.
ICD dongle for programming debugging user program
16 nos Flying leads with female bergs for extending IO lines

 

 

SPECIFICATIONS
Features of PIC16F877A
  8K x 14 words of FLASH Program Memory.

368 x 8 bytes of Data Memory (RAM).

256 x 8 bytes of EEPROM Data Memory.

One External Interrupt pin.

Three programmable Timer/Counters.

Two Capture/Compare/PWM (CCP) modules.

SPI, I2C, USART

8-channel, 10bit ADC.

In-Circuit Serial Programming™ (ICSP™) via two pins.

MPLAB® In-Circuit Debug (ICD) via two pins.
Operating Frequency - 8 MHz .
RS232 compatible serial interface for communication
Alphanumeric 16x2 LCD display.
Two numbers of general purpose LED’s.
Three numbers of push button Switches. One push button switch for reset and other two push button switches are general-purpose.
Two numbers of 20-pin single row Berg Sticks connected from Port A to Port E.
PIC CCS Evaluation Version.
Demo programs for LCD, USART, LED switches.
ICD dongle for programming debugging user program
16 nos Flying leads with female bergs for extending IO lines

 

 

SPECIFICATIONS
Useful as base board to develop project
Large amount of prototyping area (SMD & Through Hole) available
Two UARTs available as 3 wire RS232 ports (For SM2148)
Connector for 16x2 Alphanumeric LCD (For SM2148)
All port pins available on FRC connector for direct connection with other circuit
Serial cable provided.
SM2148 : LPC2148 based add on module
Supported microcontrollers: LPC2148 (ARM7TDMI architecture)
BOARDS PROVIDED WITH:
POWER ADAPTOR
FREE VERSION OF ‘C’ COMPLIER

 

 
SPECIFICATIONS

MSP430F44x is a “Texas Instruments” Low Power 16-bit Microcontroller Operating at 3.3V DC. The MSP430F44x processor is based on Reduced Instruction Set (RISC) architecture, and the instruction set and related decode mechanism are much simpler than those of micro programmed Complex Instruction Set Computers. This simplicity results in a high instruction throughput and impressive real-time interrupt response from a small and cost-effective processor Core.

The controller includes the following features:
60KB + 256B flash Program Memory.
2KB Static RAM.
48 I/O lines (Six ports of Eight bit each).
Four low power operating modes.
Three 16-bit Timers/Counters.
Capture, Compare and PWM modules.
On Chip Comparator.
Two UART multiplexed with SPI.
12-bit ADC with 8 Channel and internal reference.
Integrated LCD driver for up to 40 segments.
Onchip JTAG debugging and programming capability.
Internal Digital Controlled Oscillator in range of 0.6 to 46 MHz.
Two Software Selectable External crystal XT1 (32.768 kHz) and XT2 (450 kHz – 8 MHz).
Processor wake-up from Power-down mode via external interrupt.
Individual enable/disable of peripheral functions for power optimization.
ON BOARD INTERFACES:
3 ½ digit LCD display directly interfaced to controller.
RS232C Serial interface through onchip UART and 9 pin D-sub connector.
SPI interface to NVROM, 12 bit ADC and 12-bit DAC.
Multiturn preset and temperature sensor to study onchip 12-bit ADC.
Input switches and output LED’s connected to port lines.
Circuit to test onchip Compare, Capture, PWM and Comparator.
16x2 alphanumeric display with back lighting.
Push button and switch for resetting and programming the controller.
Unused controller lines terminated in berg headers.
A number of Software examples in ‘C language’ to illustrate the functioning of the interfaces and the low power modes. The software examples are compiled using an evaluation version of ‘C’ compiler.
External programming adapter interfaced to COM port of PC, to download code to controller Flash memory.

 

 

SPECIFICATIONS
Experimental board for 40/28/18 pin PIC Family of Microcontrollers

IC’s supported:
40 Pin Devices
16F871, 16F874, 16F877A

16F74, 16F77

18F4420, 18F4520
28 Pin Devices
16F870, 16F872, 16F873, 16F876

16F73, 16F76

18F2420, 18F2520
18 Pin Devices
16F88, 16F87, 16F84

16F62X,16F64X
Features of typical PIC Controller PIC16F877A :
Flash Program memory- 8K x 14 words

Data memory-368bytes, EEPROM memory-256 bytes

Fifteen external interrupt pins

Two Capture/Compare/PWM (CCP) module

SPI(Master), I2C(Master/Slave), USART

Multi-channel 10bit ADC

In-Circuit Serial Programming™ (ICSP™) via two pins

MPLAB® In-Circuit Debug (ICD) via two pins
Operating Frequency - 4 MHz
RS232, RS485 compatible serial interface for communication
Alphanumeric 16x2 LCD display
Four no’s of 7-seven segment display
Eight no’s of general purpose LED’s
Six no’s of general-purpose push button Switches
A Push button switch for Reset
Stepper Motor, DC Motor, Relay and Buzzer Interface
4x4 Matrix Keypad
I2C EEPROM
SPI ADC
Temperature sensor
Real Time Clock with lithium ion battery
Capture, Compare, PWM modules interface
2pin Reliamate to feed external pulse for counting
One no. of 26-pin FRC MALE connected to Port B, Port C and Port D for ALS Standard Interface boards
9 Pin DSUB Male for Power (5V, 1A)
PIC CCS Compiler - Evaluation Version
Demo programs for LCD, USART, ADC, BUZZER, CAPTURE, COMPARE, PWM, I2C, SPI, KEYPAD, STEPPER, DC motor, RELAY etc.
USB ICD dongle for programming debugging user program for devices with ICD feature - provided with evaluation board
USB ICSP programmer for devices w/o ICD capability- provided with evaluation board
IC’s supplied with evaluation board– 1no 16F877A , 1no 16F876A , 1 no 16F84
Stepper motor and DC motor are also included with the evaluation board

 

 

SPECIFICATIONS

ATMEGA128 is a Low power, high performance 8-bit Microcontroller operating at 5 VDC. The controller is based on Reduced Instruction Set (RISC) architecture, and the instruction set and related decode mechanism are much simpler than those of micro programmed Complex Instruction Set Computers. This simplicity results in a high instruction throughput.

The controller includes the following features:
128KB flash program memory.
4KB Internal Static RAM (SRAM).
4KB of internal EEPROM.
Up to 64KB optional External Read/Write memory space.
53 Programmable I/o lines.
On chip JTAG debugging and programming capability.
On chip In-System Programming (ISP) Capability.
Two 8-bit Timer/Counter and Two 16 –bit Timer/Counter
Capture, Compare and PWM modules.
On chip 8 Channel, 10-bit ADC module
Dual Programmable Serial USART’s.
Master/Slave SPI Serial Interface.
On-chip Two wire Serial Interface (I2C)
Watchdog Timer with On-chip oscillator.
On-chip analog Comparator.
Eight external Interrupts.
ON BOARD INTERFACES:
16x2 alphanumeric display (LCD) with back lighting.
4x4 Keypad Interface.
Circuit to test on-chip Compare, Capture, PWM and Comparator.
RS232C Serial interface through on chip UART0 and 9 pin D-sub connector.
5 VDC Relay Interface.
On-board multiturn preset to study on-chip 12-bit ADC.
On Board Thermistor, LDR Interface Circuit.
Suitable Proximity sensor interface circuit.
On-board interface to SPI compatible 12-bit ADC device.
On-board interface to I2C compatible NVROM.
On-board DC Motor and Stepper Motor interface.
ISP downloading tool to download the code to controller Flash memory.
The software examples are compiled using WINAVR GCC compiler.
Unused controller lines terminated in berg headers.
Power supply adapter 230VAC to 5VDC, 1A.

Note: Suitable Proximity Sensor, DC Motor and Stepper Motor will be supplied

Experiments in Embedded C:

Program to study external interrupts on rising edge, falling edge and low logic level.
Program using Timer0 in interrupt mode to generate square wave.
Program using Timer1 in compare mode.
Program using Timer1 in Capture mode (rising and falling edge).
Program using Timer1 to generate PWM output.
Program using Timer0 in Counter mode to count the incoming pulses.
Note: Timer Programs include Pre-scaler selection.
Program to test on chip watchdog timer.
Program to test on chip Comparator.
Program to read internal EEPROM.
Program to write a byte to internal EEPROM.
Program to test the LCD module.
Program to read the key pressed in 4x4 keypad matrix and display the key on LCD.
Program to receive the character serially from PC and transmit the same from target board to PC through UART.
Program to Switch ON/OFF the on board Relay.
Program to read the temperature from on board thermistor sensor using on chip ADC channel-0 and display the temperature on LCD (Features channel selection through on chip Mux).
Program to study LDR sensor.
Program to read the voltage from on board Preset using on chip ADC channel-1 and display the voltage value on LCD.
Program to test on-board SPI compatible ADC device.
Program to test on-board I2C compatible NVROM.
Program to operate DC motor.
Program to operate Stepper motor.